|
Material: 5/8" Round; 416 Stainless
Dimensions: 0.625" dia. X 2.400"
Cycle time: 72 sec.
Notes:
0.10" grooves to +/- .001;
0.375 drill through
Material: 0.197" Round; 304 Stainless
Dimensions: 0.197" X 4.000"
Cycle time: 60 sec.
Notes:
0.120 diameter drill to 2" deep
Material: 1/2" Round; 1117 CRS
Dimensions: 0.450" dia. X 1.075"
Cycle time: 42 sec.
Notes:
0.25" hex hole to depth of 0.25";
0.093 hole through
Material: 5/8" Round; Delrin AF
Dimensions: 0.610" dia. X 1.400"
Cycle time: 28 sec.
Notes:
Dual in-line cross holes;
0.4" dia. hole to 1.3" depth
Material: 1/2" Square; C110 Copper
Dimensions: 0.500" X 1.800"
Cycle time: 47.7 sec.
Notes:
0.40" deep hole drill w/ 1 OD and 2 ID threads
Material: 7/8" Round; Brass
Dimensions: 0.800" dia. X 1.55"
Cycle time: 30 sec.
Notes:
0.160" drill to 1.3";
In-line cross holes
Material: 1.0" Round; CRS
Dimensions: 0.875" dia. X 4.575"
Cycle time: 36 sec.
Notes:
3.925" OD thread;
0.575 drill to 4.475" deep
Material: 5/8" Round; Stainless
Dimensions: 0.600" dia. X 0.625"
Cycle time: 80 sec.
Notes:
Deep bottom tap ID thread
Material: 1.0" Round; Brass
Dimensions: 0.950" dia. X 1.675"
Cycle time: 36 sec.
Notes:
0.057" hole to 1" deep;
0.275" 3/4-16 thread
Material: 3/4" Round; 6061 Aluminum
Dimensions: 0.750" dia. X 1.100"
Cycle time: 28 sec.
Notes:
Radius on large end;
0.41" thin well (0.04") drill through on small end
Material: 3/8" Round; 12L14 CRS
Dimensions: 0.375" dia. X 3.625"
Cycle time: 50 sec. primary; 35 sec. secondary
Notes:
3.125" 1/4-28 thread, 0.125 drill to 2" on primary;
Drill and broach head on secondary
Material: 3/4" Round; Brass
Dimensions: 0.750" X 0.500"
Cycle time: 15 sec.
Notes:
0.330 square broach bottom hole;
0.500 ID round hole to depth of 0.375
Material: 11/16" Round; 6061 Aluminum
Dimensions: 0.660" X 1.690"
Cycle time: 31.5 sec.
Notes:
Tolerance on grooves and ID is +/-.001;
ID is 20 finish
Material: 1.0" Round; CRS
Dimensions: 0.875" dia. X 4.575"
Cycle time: 36 sec.
Notes:
3.925" OD thread;
0.575 drill to 4.475" deep
Material: 3/8" Round; 12L14 CRS
Dimensions: 0.375" dia. X 3.625"
Cycle time: 50 sec. primary; 35 sec. secondary
Notes:
3.125" 1/4-28 thread, 0.125 drill to 2" on primary;
Drill and broach head on secondary
Material: 1/2" Round; 1117 CRS
Dimensions: 0.450" dia. X 1.075"
Cycle time: 42 sec.
Notes:
0.25" hex hole to depth of 0.25";
0.093 hole through
Material: 15/16" Hex; Aluminum
Dimensions: 0.945" dia. X 0.500"
Cycle time: 27 sec.
Notes:
0.175" rolled thread on small end OD
Material: 13/16" Round; 1018 CRS
Dimensions: 0.810" dia. X 0.750"
Cycle time: 36.3 sec. + 34 sec. for tap
Notes:
7/16-10 double lead tap
Material: 3/8" Round; 1018 CRS
Dimensions: 0.375" dia. X 4.000"
Cycle time: 25 sec.
Notes:
2.5" long 3/8-16 thread
Material: 9/16" Round; Copper
Dimensions: 0.565" dia. X 1.425"
Cycle time: 52 sec.
Notes:
0.5" fine thread;
Very good finish on smooth end
Material: 13/16" Round; Aluminum
Dimensions: 0.795" dia. X 0.450"
Cycle time: 26 sec.
Notes:
ID thread very close to bottom
Material: 1" Square; 12L14 CRS
Dimensions: 1.000" sq. X 0.375"
Cycle time: 30 sec.
Notes:
1/2-20 ID thread;
0.20" knurl on 0.875" round end
Material: 2-1/8" Round; Aluminum
Dimensions: 2.075" dia. X 2.075"
Cycle time: 51 sec.
Notes:
0.625" long 1-1/4 bump roll thread
Material: 1/2" Square; C110 Copper
Dimensions: 0.500" X 1.800"
Cycle time: 47.7 sec.
Notes:
0.40" deep hole drill w/ 1 OD and 2 ID threads
Material: 3/4" Hex; 304 Stainless
Dimensions: 0.750" dia. X 3.375"
Cycle time: Primary--65.3 sec. ID thread;
Secondary--100 sec. OD thread
Material: 1.0" Round; Brass
Dimensions: 0.950" dia. X 1.675"
Cycle time: 36 sec.
Notes:
0.057" hole to 1" deep;
0.275" 3/4-16 thread
Material: 1-1/2" Round; 316 Stainless
Dimensions: 1.435" dia. X 0.125" thick
Cycle time: 40 sec.
Notes:
32 to 42 rms finish on both sides without secondaries;
Parallel surfaces flat to within .002"
Material: 1/3" Round; Delron
Dimensions: 0.336" dia. 1.6"
Cycle time: 32.1 sec.
Notes:
Narrow grooves
Material: 1/2" Round; Brass
Dimensions: 0.500" dia. X 2.750"
Cycle time: 20 sec.
Notes:
1.9" diamond knurl
Material: 2-3/8" Round; Brass
Dimensions: 2.375" dia. X 0.750"
Cycle time: 29 sec.
Notes:
Excellent finish on curved radius
Material: 1/3" Round; 316 Stainless
Dimensions: 0.336" dia. 1.6"
Cycle time: 61.8 sec.
Notes:
Narrow grooves
Material: 7/16" Round; Aluminum
Dimensions: 0.400" dia. X 2.100"
Cycle time: 31.5 sec.
Notes:
Larger OD with narrow grooves
Material: 1-3/4" Round; Brass
Dimensions: 1.710" dia. X 2.100"
Cycle time: 34.8 sec.
Notes:
0.25" ID thread at 0.300" depth large end;
Exceptional finish
|
